what is the ratio of M10,M20,M30,M40,M50,M60 grade concrete..

Get Price# m30 grade of concrete ratio

Sep 21, 2015· mix design m30 1. design a concrete for strength m30 ( w ͽͽ ) specification of materials: a) grade designation : m30 b) type of cement : opc 53 grade c) max nominal size of : 20mm down aggregate d) min. cement contnt : 320 ͭx ͽ e) water cement ratio : f) workability : 75mm slump g) exposer condition : severe () h) method of concrete : manual placing i) max.

Get PriceThe strength of concrete is divided into twelve grades such as , C10, C15, C20, C25, C30, C35, C40, C45, C50, C55 and C60. Concrete mix ratios are expressed in two ways: one is expressed in materials used per cubic meter of concrete (Water: Cement: Sand: Gravel), and the other is expressed as a ratio of various materials. for example, C:S:G ...

Get PriceTherefore, an appropriate grade of concrete can be selected based on structural requirements. Nominal mixtures for concrete types such as M15, M20, M25 are generally used for smallscale construction. Large structures have high strength requirements and are therefore used for higher grades of concrete, such as M30 and above. The mixing ...

Get PriceConcrete mix design is required to achieve target strength in structures. Concrete Mix design calculation of M20, M25, M30 grade of concrete with example.

Get PriceMix design of M30 grade concrete Projects requirements . 1 Mix design of : M30 grade concrete 2 Type of cement used PPC cement ( supplied only with strength of 33 grade as per clause no page no 2 of IS 1489 ). conforming to IS 1489 Part 1. Maximum nominal size of aggregate: 20 Exposure condition : Moderate exposure condition 5 Workability : mm 50 mm (slump)

Get PriceM40 grade stands for it’s a mix of concrete with a characteristic compressive strength of 40 N/mm2. The mix design procedure for M40 grade concrete as per ACI Method is discussed. Contents:M40 Grade Concrete Mix Design Procedure1. Required Data2. Mean Design Strength3. WaterCement Ratio4. Water Content and Air Content5. Cement Content6.

Get PriceThe basic requirements for the design of concrete mix ratio are: 1, meet the strength grade of concrete design. 2, meet the concrete peaceability. 3, meet the durability of the use of concrete. 4, meet the above conditions to save cement and reduce the cost of concrete. The strength of concrete is divided into twelve grades, such as , C10 ...

Get PriceThe maximum watercement ratio to design M30 grade concrete can be found from Table 5IS456 given above. You can reduce the watercement ratio for M30 grade concrete based on your requirements, but remember that Watercement ratio directly affects the strength of the concrete. V. SELECTION OF WATER CONTENT

Get PriceConcrete grades are denoted by M10, M20, M30, according to their compressive strength. The “M” denotes Mix design of concrete followed by the compressive strength number in N/mm2, “ Mix” is the respective ingredient proportions which are Cement: Sand: Aggregate Or Cement: Fine Aggregate: Coarse Aggregate.

Get PriceThis paper discussed an experimental study of M30 Grade of concrete using fly ash, steel fiber, cement, coarse aggregate and fine aggregate. Fly ash is the waste material produced from many thermal power. The disposal of fly ash is the one of major

Get PriceConcrete grades are denoted by M10, M20, M30 according to their compressive strength. The “M” denotes Mix design of concrete followed by the compressive strength number in N/mm 2 “Mix” is the respective ingredient proportions which are Cement: Sand: Aggregate Or Cement: Fine Aggregate: Coarse Aggregate.

Get PriceConcrete Mix design of M5, , M10, M15, M20, M25, M30 and higher grades of concrete is calculated as below: The procedure for finding the different grades of concrete mixes are same. The below mentioned method can be applied to any grade of concrete by changing the values.

Get PriceAug 20, 2019· Concrete mix proportion of M30 grade of concrete In this process furma are used for raw materials and the unit of furma have in liters. So I provided all raw materials quantity directly in liters.

Get PriceFor example, for M30 grade, the mix proportion can be 1:1:2, where 1 is the ratio of cement, 1 is the ratio of sand and 2 is the ratio of coarse aggregate based on volume or weight of materials. The strength measure with concrete cube or cylinders by civil engineers at the construction site.

Get Price